'
1
Forums Albums Skins 1
Search Register Logon


You are logged in as a guest. Logon or register an account to access more features.
OTHER FORUMS:    Barrel Horses  -   Trucks   -   Cutting  -   Reining  -   Roping 
'
Question about Sealing Floor in LQ

Jump to page : 1
Now viewing page 1 [25 messages per page]
Last activity 2009-04-03 4:36 PM
7 replies, 4935 views

View previous thread :: View next thread
   General Discussion -> Trailer Talk  Click to return to Barrel Talk
Refresh
Message format
 
Rose66
Reg. Dec 2006
Posted 2009-03-12 1:51 PM (#101204)
Subject: Question about Sealing Floor in LQ


Veteran


Posts: 136
10025
Location: Alabama
In my LQ area, I have floor insulation and then a piece of OSB plywood for the floor and I plan on putting down viny flooring. Since the OSB is not treated wood, I want to put something on it to seal it before I put down vinyl flooring. My first thought was Thompson's WaterSeal however, the people at Thompson's have told me that no floor adhesive will stick to their sealant. Does anyone know of some type of sealant I can put on the wood that will then allow me to put adhesive vinyl flooring down?

I thought about replacing the OSB wood with treated plywood but since my furring strips are attached to the OSB floor, it would be much easier to simply seal the floor rather than replace it.

Thanks!
share Top of the page Bottom of the page
gard
Reg. Aug 2007
Posted 2009-03-12 7:35 PM (#101233 - in reply to #101204)
Subject: RE: Question about Sealing Floor in LQ


Expert


Posts: 5870
50005001001001002525
Location: western PA

Coat the OSB with a couple of coats of oil or water based polyurethane varnish. This will seal and waterproof the wood chips. After it drys, rough up the surface with some coarse sandpaper to allow better adhesion with the flooring material.

Gard

share Top of the page Bottom of the page
Rose66
Reg. Dec 2006
Posted 2009-03-13 1:05 AM (#101251 - in reply to #101233)
Subject: RE: Question about Sealing Floor in LQ


Veteran


Posts: 136
10025
Location: Alabama
Thanks Gard! Do you know for sure that floor adhesive will stick to roughened up polyurethane varnish?

share Top of the page Bottom of the page
gard
Reg. Aug 2007
Posted 2009-03-13 8:51 AM (#101269 - in reply to #101204)
Subject: RE: Question about Sealing Floor in LQ


Expert


Posts: 5870
50005001001001002525
Location: western PA

There are many types of flooring adhesives; water based rubber, water based tile adhesives, urethane based products for hardwood flooring, asphalt based for tile and linoleum, epoxies are used in commercial situations, etc.

The cured polyurethane finishes are pretty much impervious to many of the other urethanes, as well as water and rubber based products. Some epoxies are very aggressive, and could destroy the varnish coating. If you are using an epoxy, you would not need to pre seal the wood first. A complete application of the adhesive itself would be enough.

Many of these adhesive products will also seal the wood upon application, and you may not need the varnish. If you were to read the application instructions of the individual products, you may gain additional insight.

Gard

share Top of the page Bottom of the page
AQHA 123
Reg. Oct 2008
Posted 2009-04-03 3:27 PM (#102707 - in reply to #101204)
Subject: RE: Question about Sealing Floor in LQ


Veteran


Posts: 241
10010025
Gard, If I use pressure treated plywood, and strips of pressure treated wood under that I dont need to treat it-- is that right?
share Top of the page Bottom of the page
gard
Reg. Aug 2007
Posted 2009-04-03 4:03 PM (#102708 - in reply to #102707)
Subject: RE: Question about Sealing Floor in LQ


Expert


Posts: 5870
50005001001001002525
Location: western PA

Originally written by AQHA 123 on 2009-04-03 3:27 PM

Gard, If I use pressure treated plywood, and strips of pressure treated wood under that I dont need to treat it-- is that right?

Yes, that is correct

share Top of the page Bottom of the page
dawnb
Reg. Aug 2007
Posted 2009-04-03 4:29 PM (#102712 - in reply to #101204)
Subject: RE: Question about Sealing Floor in LQ


Veteran


Posts: 214
100100
Location: lyle,mn
make sure that the treated wood is not AQC. That stuff eats metal.
share Top of the page Bottom of the page
AQHA 123
Reg. Oct 2008
Posted 2009-04-03 4:36 PM (#102714 - in reply to #101204)
Subject: RE: Question about Sealing Floor in LQ


Veteran


Posts: 241
10010025
10-4
share Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [25 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread
Message format
 

'
Registered to: Horse Trailer World
(Delete all cookies set by this site)